Record your screen in PowerPoint

7/15/2019

You can record your computer screen and related audio, and then embed it in your PowerPoint slide—or you can save it as a separate file.

To record and listen to audio associated with your screen recording, you'll need a sound card, microphone, and speakers.
Make sure there's enough disk space on your local drive to record and save your screen recording.

Record from your computer screen and embed the recording in PowerPoint

Newer versions (click Office 2013 if you are using Office 2013)

Open the slide that you want to put the screen recording on.
On the Insert tab of the ribbon, select Screen Recording.

On the Control Dock, click Select Area (Windows logo key+Shift+A), or, if you want to select the entire screen for recording, press Windows logo key+Shift+F.

(The Windows logo key+Shift+F keyboard shortcut is only available if you have an Office 2016 Click-to-Run installation; MSI-based installations don't have the shortcut. Additionally, the minimum required version of Office for the shortcut is 16.0.7571.2072.)

The minimum size area you can record is 64x64 pixels.

If you have opted to select an area, you see the cross-haired cursor . Click and drag to select the area of the screen you want to record. (If you have already done a screen recording during your current PowerPoint session, your prior area selection will appear on the screen. You can proceed with recording if that selection area suits you, or you can click Select Area to start over.)

Tip: PowerPoint automatically records the audio and the mouse pointer, so by default those options are selected on the control dock. To turn them off, deselect Audio (Windows logo key+Shift+U) and Record Pointer (Windows logo key+Shift+O).

Click Record (Windows logo key+Shift+R).

Tip: Unless you pin the Control Dock to the screen, it will slide up into the margin while you record. To make the unpinned Control Dock reappear, point the mouse cursor at the top of the screen.

To control your recording:
- Click Pause to temporarily stop the recording (Windows logo key+Shift+R).
- Click Record to resume recording (Windows logo key+Shift+R).
- Click Stop to end your recording (Windows logo key+Shift+Q) (shown below).

When you are finished recording, save your presentation: File > Save. The recording is now embedded on the slide you selected in step 2.

To save the recording itself as a separate file on your computer, right-click the picture on the slide that represents the recording, and select Save Media as. In the Save Media As dialog box, specify a file name and folder location, then click Save.

Save your screen recording as a separate file from PowerPoint

If you are using PowerPoint 2013, before you try to save your screen recording as a separate file, check to make sure you have installed all the required updates:

Install version 15.0.4641.1001 or later for the Click-to-run version.
Install both of these updates (KB2883051 and KB2883052) for all versions except Click-to-run.

Once you have installed the correct updates, you can save the video file. Here's how:

Right-click the video frame, and click Save Media as.

Tip: Ensure your disk has enough space to save the video file. Otherwise, you'll have to free up space and try again.

In the Save Media as box, choose a folder, and in the File name box, type a name.
Click Save.

Set your video 'Start' settings

Right-click the video frame, click Start, and pick how you want your video to start in your presentation; automatically when a slide appears, or when you click the mouse.

Trim your video

Right-click the video frame, and click Trim.

To determine where you want to trim your video footage, in the Trim Video box, click Play.
When you reach the point where you want to make the cut, click Pause.

Tip: Use the Next Frame and Previous Frame buttons to specify precise timing.

Do one or more of the following:
- To trim the beginning of the clip, click the start point (shown in the image below as a green marker). When you see the two-headed arrow, drag the arrow to the desired starting position for the video.

- To trim the end of the clip, click the end point (shown in the image above as a red marker). When you see the two-headed arrow, drag the arrow to the desired ending position for the video.
Click OK.

Apply a style to the video frame

Right-click the video frame, click Style, and pick a style you like.

Other Tips and Tricks

3/9/2026

Tiếng Việt

Record your screen in PowerPoint

Other Tips and Tricks

5 Excel Functions That Replace 41 Others

How to Freeze Multiple Rows in Excel

Everything You Need to Know About Power Automate

COPILOT Function in Excel: 17 Practical Ways to Save Time and Clean Data

Power Query Tutorial: 7 Essential Tips to Master Data Transformation in Excel

© Copyright 2018 Tan Duc ITS